Switch 1.3.0 Release Notes
Version 1.2.0.1
May 2023
Compatibility and Installation Notes
The SonicWall Switch 1.2.0.1 release is supported on all SonicWall Switch platforms:
- SWS12-8
- SWS12-8POE
- SWS12-10FPOE
- SWS14-24
- SWS14-24FPOE
- SWS14-48
- SWS14-48FPOE
For information about obtaining the latest Switch firmware and upgrading the firmware image on your SonicWall Switch, see the Switch Getting Started Guide available on the Support portal at Switch Getting Started Guide.
What's New
-
Tool tips were added to the LLDP timers and for MSTP since it is a supported STP protocol.
-
The TCP Flag name was added in the IPv4 ACE header row for easy identification.
Resolved Issues
| Issue ID | Issue Description |
|---|---|
| SWO-1855 | SonicWall Switch stops working sporadically with SNMP V3 enabled or SNMP disabled, and switches are working fine |
| SWO-1754 | Not able to edit or delete the SNMP Group |
| SWO-1744 | VoIP phones are not getting DHCP IP from the Voice VLAN subnet |
| SWO-1713 | The Apply button is not grayed out if the limit exceeds for RMON configuration and there is no pop-up message on the screen. |
| SWO-1712 | User should not be allowed to enter out of range Source and Destination port values. |
| SWO-1708 | The new PoE switch model switches like SWS12-8PoE, SWS12-10FPoE,SWS14-24FPoE, and SWS14-48FPOE running Switch image 1.2.0.0 by default and above cannot be downgraded to 1.1.1.0 and below versions. |
| SWO-1705 | Issue adding Target Address under SNMP. |
| SWO-1702 | Unable to delete Group List under SNMP tab. |
| SWO-1697 | High Latency & Ping drop after firmware upgrade on 48 Port Switch-1.1.0.2-17s |
| SWO-1694 | The active firmware display page does not show the firmware version clearly in Firmware Images tab |
| SWO-1661 | Ping to an IP in local subnet fails when tried from UI |
| SWO-1649 | SFP ports with transceivers are not active when using Auto-Negotiate |
| SWO-1618 | Add Mac Entries text showing two times in MAC Adress Table section |
| SWO-1605 | Switch IPv4 ACE list - Header row contents are not fully shown |
| SWO-1599 | Reaching maximum number of ipv4 acl should display proper error message |
| SWO-1590 | Under QOS > Class mapping table does not show complete information |
| SWO-1589 | Under QOS name of Class map should not accept negative numbers and special characters. |
| SWO-1582 | Under QOS > Advanced policy, creating new class policy with invalid mac address fails to throw error |
| SWO-1558 | Binding ACL to ports should throw success prompt |
| SWO-1551 | Adding duplicate entry for ipv4 ACL throws wrong error message |
| SWO-1544 | Class map name should support only characters and positive numbers |
| SWO-1543 | The character limit shown in the tooltip is incorrect for the name of the class map under QOS |
| SWO-1533 | Unable to create a static route with subnet mask as 255.255.255.255 |
| SWO-1439 | The issue in adding the target address under SNMP |
| SWO-1046 | Subnet Mask always saving as 255.255.255.255. When the user tried to save in CIDR subnet mask notation |
| SWO-1044 | The user can save Switch Network IP with invalid IPs (like Loopback IP and Multicast IP). |
| SWO-764 | Unable to download or export switch logs from standalone switch UI |
Known Issues
No additional known issues.
Was This Article Helpful?
Help us to improve our support portal