• SonicOS 7.0
• High Availability
  • About High Availability
    • High Availability Terminology
    • High Availability Modes
    • High Availability Encryption
    • Crash Detection
    • Virtual MAC Address
    • Dynamic WAN Interfaces with PPPoE HA
    • Stateful Synchronization with DHCP
    • Stateful Synchronization with DNS Proxy
    • About HA Monitoring
  • About Active/Standby HA
    • Benefits of Active/Standby HA
    • Working of Active/Standby HA
  • About Stateful Synchronization
    • Benefits of Stateful Synchronization
    • How Does Stateful Synchronization Work?
    • Example of Stateful Synchronization
  • Active/Standby Prerequisites
    • Supported Platforms and Licensing for HA
    • Physically Connecting Your Security Appliances
  • Maintenance
    • Removing an HA Association
    • Replacing a SonicWall Security Appliance
      • Replacing an HA Primary Unit
      • Replacing an HA Secondary Unit
• High Availability Status
  • Active/Standby High Availability Status
    • High Availability Status
    • High Availability Config
    • High Availability Licenses
• Configuring High Availability
  • Configuring Active/Standby High Availability Settings
  • Configuring HA with Dynamic WAN Interfaces
• Configuring High Availability in the Cloud Platform
  • Set up an Active/Standby High Availability Configuration Using Azure
    • Install the Custom Template
    • Enable Identity of Both Virtual Machines (HA1 and HA2)
    • Role Assignment
    • Check the Networking Tab
    • Configuring Active NSv Firewall Using the Associated Public IP
    • Configuring Standby NSv Firewall Using the Associated Public IP
    • Enable the L3 Mode
    • Configuring Active NSv Firewall Using the Floating Public IP
    • Configuring HA to Active/Standby with L3 HA link
    • Adding Additional Floating Public IP
• Fine Tuning High Availability
  • Advanced Settings
  • Configuring Advanced High Availability Settings
• Monitoring High Availability
  • Configuring Active/Standby High Availability Monitoring
  • IPv6 High Availability Monitoring
  • IPv6 HA Monitoring Considerations
• Azure Use Cases
  • Use Case 1: Manage Azure HA Firewall
  • Use Case 2: Forward LAN traffic to the External Network through the Gateway after HA Failover
  • Use Case 3: Configure DNAT on Azure HA Firewall
  • Use Case 4: Configure DNAT on Azure HA Firewall (Need to move multiple floating IPs support)
• SonicWall Support
  • About This Document

Removing an HA Association

You can remove the association between two SonicWall Security Appliances on MySonicWall at any time. You might need to remove an existing HA association if you replace a Security Appliance or reconfigure your network. For example, if one of your SonicWall Security Appliances fails and you need to replace it, or you might need to switch the HA Primary Security Appliance with the Secondary, or HA Secondary, unit after a network reconfiguration. In either case, you must first remove the existing HA association, and then create a new association that uses a new Security Appliance or changes the parent-child relationship of the two units (see Replacing a SonicWall Security Appliance).

To remove the association between two registered SonicWall Security Appliances:

1. Log in to MySonicWall.
2. In the left navigation bar, navigate to My Workspace > Tenant Products.
3. Scroll down to find the secondary Security Appliance from which you want to remove associations. Click the serial number.
4. On the Products Details page, scroll down to the Parent Products section, just below the Associated Products section.
5. Under Parent Products, to remove the association for this Security Appliance:
   1. Click Remove under ACTIONS.
   2. Wait for the page to reload.
   3. Scroll down.
   4. Click Remove again.