• SonicOS 7.0 Rules and Policies
• Settings
  • Configuring App/Match/Malware
  • Configuring Content Filtering Service (CFS)
    • SonicWall CFS
    • CFS Custom Category
  • Geo-IP
    • Custom List
      • Editing a Custom List Entry
      • Deleting Custom List Entries
    • Using Geo-IP Diagnostics
  • Botnet
    • Configuring Botnet Settings
    • Creating Custom Botnet Lists
    • Viewing Dynamic Botnets Lists
    • Configuring a Dynamic Botnet List Server
    • Using Botnet Diagnostics
  • Decryption (DPI-SSL)
    • Certificate
    • Common Name
    • SSL Servers
  • Decryption (DPI-SSH)
  • Signature Update
• Security Policy
  • User & Country
  • App/URL/Custom Match
• NAT Policy
  • About NAT in SonicOS
  • About NAT Load Balancing
    • Determining the NAT LB Method to Use
    • Caveats
    • How Load Balancing Algorithms are Applied
    • Sticky IP Algorithm Examples
      • Example One - Mapping to a Network
      • Example Two - Mapping to an IP Address Range
  • About NAT64
    • Use of Pref64::/n
  • About FQDN-based NAT
  • About Source MAC Address Override
  • Viewing NAT Policy Entries
    • Changing the Display
    • Filtering the Display
  • Adding or Editing NAT or NAT64 Rule Policies
  • Deleting NAT Policies
  • Creating NAT Rule Policies: Examples
    • Creating a One-to-One NAT Policy for Inbound Traffic
    • Creating a One-to-One NAT Policy for Outbound Traffic
    • Inbound Port Address Translation via One-to-One NAT Policy
    • Inbound Port Address Translation via WAN IP Address
    • Creating a Many-to-One NAT Policy
    • Creating a Many-to-Many NAT Policy
    • Creating a NAT Load Balancing Policy for Two Web Servers
• Routing
  • About Routing
    • About Metrics and Administrative Distance
      • About Metrics
      • About Administrative Distance
    • Route Advertisement
    • ECMP Routing
    • Policy-based Routing
    • Policy-based TOS Routing
    • PBR Metric-based Priority
    • Policy-based Routing and IPv6
    • OSPF and RIP Advanced Routing Services
      • About Routing Services
        • Protocol Type
        • Maximum Hops
        • Split-Horizon
        • Poison Reverse
        • Routing Table Updates
        • Subnet Sizes Supported
        • Autonomous System Topologies
      • OSPF Terms
    • Drop Tunnel Interface
    • App-based Routing
  • Rules and Policies > Route Policy
    • Configuring Route Policies
      • Adding Static Routes
      • Probe-Enabled Policy-based Routing Configuration
• Decryption Policy
  • Client-side SSL Rules
  • Server-side SSL Rules
  • SSH Rules
  • Setting up the Decryption Policy Table
    • Managing the Decryption Policy Toolbars
    • Changing the Policy Priority
    • Creating Decryption Policies
      • Adding Decryption Policies
      • Editing Decryption Policies
      • Deleting Decryption Policies
• DoS Policy
  • Setting up the DoS Policy Table
    • Managing the DoS Policy Toolbars
    • Changing the DoS Policy Priority
    • Creating DoS Policies
      • Adding DoS Policies
      • Editing DoS Policies
      • Deleting DoS Policies
• DNS Policy
  • Creating DNS Policies
    • Adding DNS Policies
    • Editing DNS Policies
    • Deleting DNS Policies
  • DNS Doctoring
• Endpoint Policy
• Shadow
• SonicWall Support
  • About This Document

Probe-Enabled Policy-based Routing Configuration

You can optionally configure a Network Monitor policy for the route. When a Network Monitor policy is used, the static route is dynamically disabled or enabled, based on the state of the probe for the policy.

Policy-based Routing is fully supported for IPv6 by selecting IPv6 address objects and gateways for route policies on the POLICY | Rules and Policies > Routing Policy page. IPv6 address objects are listed in the Source, Destination, and Gateway columns of the Route Policies table. Configuring routing policies for IPv6 is nearly identical to IPv4.

To configure a policy-based route

1. Navigate to the POLICY | Rules and Policies > Routing Policy page.

2. Click +Add (in the bottom left corner). The Adding Rule dialog displays.

   

3. Click the Probe view and select the appropriate Probe Network Monitor object or select Create a new Network Monitor Object... to dynamically create a new object.

   Typical configurations do not have Disable route when probe succeeds checked because typically a route is disabled when a probe to the route’s destination fails. This option is provided to give you added flexibility for defining routes and probes.

4. Select the Probe default state is UP to have the route consider the probe to be successful (such as in the UP state) when the attached Network Monitor policy is in the UNKNOWN state. This is useful to control the probe-based behavior when a unit of a High Availability pair transitions from IDLE to ACTIVE, because this transition sets all Network Monitor policy states to UNKNOWN.

5. Click Add to apply the configuration.