• SonicWall SonicOS 7.0.1
  • Version 7.0.1-5161 July 2024
  • Version 7.0.1-5151 March 2024
  • Version 7.0.1-5145 November 2023
  • Version 7.0.1-5129 June 2023
  • Version 7.0.1-5119 June 2023
  • Version 7.0.1-5111 April 2023
  • Version 7.0.1-5100 March 2023
  • Version 7.0.1-5095 November 2022
  • Version 7.0.1-5083 September 2022
  • Version 7.0.1-5080 September 2022
  • Version 7.0.1-5072 June 2022
  • Version 7.0.1-5030-R945 May 2022
  • Version 7.0.1-5065 April 2022
  • Version 7.0.1-5054 April 2022
  • Version 7.0.1-5052 April 2022
  • Version 7.0.1-5030 December/October 2021
  • Version 7.0.1-5026 September 2021
  • Version 7.0.1-5023 August 2021
  • Version 7.0.1-5019 August 2021
  • Version 7.0.1 July 2021
  • Version 7.0.1 June 2021
  • Version 7.0.1 April 2021
• SonicWall Support
  • About This Document

Version 7.0.1-5023 August 2021

August 2021

This version of SonicOS 7.0.1 is a maintenance release for existing platforms and resolves issues found in previous releases.

Supported Platforms

The platform-specific versions for this unified release are all the same:

Platform	Firmware Version
TZ Series	7.0.1-5023
NSa Series	7.0.1-5023
NSv Series	7.0.1-5023
NSsp Series	7.0.1-5023

NSa 2700 NSa 3700 NSa 4700 NSa 6700

NSsp 13700 NSsp 15700

TZ270 / TZ270W TZ370 / TZ370W TZ470 / TZ470W TZ570 / TZ570W TZ570P TZ670

NSv 270 NSv 470 NSv 870

NSv 270/470/870 deployments are supported on the following platforms:

• AWS (BYOL and PAYG)
• Microsoft Azure (BYOL)
• VMware ESXi
• Microsoft Hyper-V
• Linux KVM

Resolved Issues

Issue ID	Issue Description
GEN7-24501	When Physical Monitoring only is enabled, the VLAN interface set as the primary WAN interface cannot failover after its parent interface is shut down.
GEN7-25650	OSPF routes not showing as Active.
GEN7-26235	Some changes on the Failover & LB pages cause unwanted reordering of LB Group values in the web management interface .
GEN7-26534	For WAN interfaces, the settings cannot be changed between Logical/Probe Monitoring enabled and Physical Monitoring only.
GEN7-26645	Changes to the User Authentication Method are not being saved when selected under User Settings.
GEN7-26741	Cannot delete unwanted address groups.
GEN7-26987	After setting the VLAN ID to 3 (on the NETWORK > Firewall > Advanced > Internal VLAN page), DHCP requests are answered from X1 instead of X0, preventing access to the web management interface.

Additional References

The following additional resolved issues in this release are listed here for reference:

GEN7-27591, GEN7-27543, GEN7-27007, GEN7-26908, GEN7-26624, GEN7-26571, GEN7-26338, GEN7-26179, GEN7-23551

Known Issues

Issue ID	Issue Description
GEN7-26785	If devices have Capture Client installed, Endpoint Enforcement does not allow access to the devices.
GEN7-27823	Configuring Ratio mode for an LB group fails with an error message: Command 'rank 1' does not match. Use the command-line interface (CLI) to configure or change to ratio-based mode.
GEN7-27849	An error is displayed when Group Always On is selected as the Exclusion Address for an App Control Policy type.