SonicOS 7 System
- SonicOS 7
- Interfaces
- About Interfaces
- Interface Settings IPv4
- Adding Virtual Interfaces
- Configuring Routed Mode
- Enabling Bandwidth Management on an Interface
- Configuring Interfaces in Transparent IP Mode (Splice L3 Subnet)
- Configuring Wireless Interfaces
- Configuring WAN Interfaces
- Configuring Tunnel Interfaces
- Configuring VPN Tunnel Interfaces
- Configuring Link Aggregation and Port Redundancy
- Configuring One Arm Mode
- Configuring an IPS Sniffer Mode Appliance
- Configuring Security Services (Unified Threat Management)
- Configuring Wire and Tap Mode
- Layer 2 Bridged Mode
- Key Features of SonicOS Layer 2 Bridged Mode
- Key Concepts to Configuring L2 Bridged Mode and Transparent Mode
- Comparing L2 Bridged Mode to Transparent Mode
- Comparison of L2 Bridged Mode to Transparent Mode
- Benefits of Transparent Mode over L2 Bridged Mode
- ARP in Transparent Mode
- VLAN Support in Transparent Mode
- Multiple Subnets in Transparent Mode
- Non-IPv4 Traffic in Transparent Mode
- ARP in L2 Bridged Mode
- VLAN Support in L2 Bridged Mode
- L2 Bridge IP Packet Path
- Multiple Subnets in L2 Bridged Mode
- Non-IPv4 Traffic in L2 Bridged Mode
- L2 Bridge Path Determination
- L2 Bridge Interface Zone Selection
- Sample Topologies
- Configuring Network Interfaces and Activating L2B Mode
- Configuring Layer 2 Bridged Mode
- Asymmetric Routing
- Configuring Interfaces for IPv6
- 31-Bit Network Settings
- PPPoE Unnumbered Interface Support
- Failover & LB
- Neighbor Discovery
- ARP
- MAC IP Anti-Spoof
- Web Proxy
- PortShield Groups
- Static and Transparent Mode
- SonicOS Support of X-Series Switches
- About the X-Series Solution
- Performance Requirements
- Key Features Supported with X-Series Switches
- PortShield Functionality and X-Series Switches
- PoE/PoE+ and SFP/SFP+ Support
- X-Series Solution and SonicPoints
- Managing Extended Switches using GMS
- Extended Switch Global Parameters
- About Links
- Logging and Syslog Support
- Supported Topologies
- Port Graphics
- Port Configuration
- External Switch Configuration
- External Switch Diagnostics
- Configuring PortShield Groups
- VLAN Translation
- IP Helper
- Dynamic Routing
- DHCP Server
- Configuring a DHCP Server
- Configuring Advanced Options
- Configuring DHCP Option Objects
- Configuring DHCP Option Groups
- Configuring a Trusted DHCP Relay Agent Address Group (IPv4 Only)
- Enabling Trusted DHCP Relay Agents
- Configuring IPv4 DHCP Servers for Dynamic Ranges
- Configuring IPv6 DHCP Servers for Dynamic Ranges
- Configuring IPv4 DHCP Static Ranges
- Configuring IPv6 DHCP Static Ranges
- Configuring DHCP Generic Options for DHCP Lease Scopes
- DHCP and IPv6
- Multicast
- Network Monitor
- AWS Configuration
- SonicWall Support
External Switch Configuration
This table displays No Data when external switches have not been provisioned.
|
ID # |
ID number of the external switch: 1, 2, 3, or 4. |
| Model | Model number of the extended switch. |
| Status |
Status of the switch: A green Enabled icon indicates the switch is up and available. When an extended switch has been powered off and then the appliance is restarted (rebooted), it might take up to five minutes before the appliance discovers the extended switch and reports the Status of the switch as up and available. |
| IP Address | IP address of the extended switch. |
| Switch Mode | Mode of the switch, such as Standalone. |
| Switch Management | Switch port used for management traffic. |
| Firewall Uplink | Port on the appliance configured as the appliance uplink. If no appliance port has been configured as the appliance uplink, the column displays None. |
| Switch Uplink | Port on the extended switch configured as the switch uplink. If no switch port has been configured as the switch uplink, the column displays None. |
| Parent Switch ID | For daisy-chained switches, the ID of the parent switch. If no switch port has been configured as the parent switch, the column displays N/A. |
| Parent Switch Uplink |
Port on a daisy-chained parent switch configured as the switch uplink. If no switch port has been configured as the parent switch uplink, the column displays N/A. |
| Configure |
Contains the:
|
External Switch Configuration provides information about the external switches provisioned on the appliance and allows you to manage the switch. You can also configure or delete an extended switch. To configure an extended switch, see PortShield Groups; to delete an extended switch, see the SonicWallX-Series Solution Deployment Guide.
Was This Article Helpful?
Help us to improve our support portal