• SonicOS 7.0 Rules and Policies
• Access Rules
  • Setting Firewall Access Rules
    • About Connection Limiting
    • Using Bandwidth Management with Access Rules
      • Enabling Bandwidth Management on an Access Rule
    • Creating Access Rules
    • Configuring Access Rules for IPv6
      • About Stateful Packet Inspection Default Access Rules
    • Enabling and Disabling Access Rules
    • Editing Access Rules
    • Deleting Access Rules
    • Restoring Access Rules to Default Settings
    • Displaying Access Rules
      • By Zones
      • By Column
    • Displaying Access Rule Traffic Statistics
    • Configuring Access Rules for NAT64
    • Configuring Access Rules for a Zone
    • Access Rules for DNS Proxy
    • User Priority for Access Rules
  • Access Rule Configuration Examples
    • Enabling Ping
    • Blocking LAN Access for Specific Services
    • Allowing WAN Primary IP Access from the LAN Zone
• NAT Rules
  • About NAT in SonicOS
  • About NAT Load Balancing
    • Determining the NAT LB Method to Use
    • Caveats
    • How Load Balancing Algorithms are Applied
    • Sticky IP Algorithm Examples
      • Example One - Mapping to a Network
      • Example Two - Mapping to an IP Address Range
  • About NAT64
    • Use of Pref64::/n
  • About FQDN-based NAT
  • About Source MAC Address Override
  • Viewing NAT Policy Entries
    • Changing the Display
    • Filtering the Display
    • Displaying Information about Policies
  • Adding or Editing NAT or NAT64 Rule Policies
  • Deleting NAT Policies
  • Creating NAT Rule Policies: Examples
    • Creating a One-to-One NAT Policy for Inbound Traffic
    • Creating a One-to-One NAT Policy for Outbound Traffic
    • Inbound Port Address Translation via One-to-One NAT Policy
    • Inbound Port Address Translation via WAN IP Address
    • Creating a Many-to-One NAT Policy
    • Creating a Many-to-Many NAT Policy
    • Creating a One-to-Many NAT Load Balancing Policy
    • Creating a NAT Load Balancing Policy for Two Web Servers
    • Creating a WAN-to-WAN Access Rule for a NAT64 Policy
    • DNS Doctoring
• Routing
  • About Routing
    • About Metrics and Administrative Distance
      • About Metrics
      • About Administrative Distance
    • Route Advertisement
    • ECMP Routing
    • Policy-based Routing
    • Policy-based TOS Routing
    • PBR Metric-based Priority
    • Policy-based Routing and IPv6
    • OSPF and RIP Advanced Routing Services
      • About Routing Services
        • Protocol Type
        • Maximum Hops
        • Split-Horizon
        • Poison Reverse
        • Routing Table Updates
        • Subnet Sizes Supported
        • Autonomous System Topologies
      • OSPF Terms
    • Drop Tunnel Interface
    • App-based Routing
  • Rules and Policies >
    • Configuring
      • Adding Static Routes
      • Probe-Enabled Policy-based Routing Configuration
• Content Filter Rules
  • About Content Filtering Rules (CFS)
    • About Content Filter Rules
    • About UUIDs for CFS Policies
    • About Content Filter Action Objects
    • How CFS Works
  • Configuring CFS Policies
    • About the Content Filter Rule Table
      • Searching the Content Filter Rule Table
    • Adding a Content Filter Rule
    • Editing a Content Filter Rule
    • Deleting Content Filter Rules
• App Rules
  • About App Rules
    • What are App Rules?
      • About App Rules Policies
      • About App Rules Capabilities
    • Benefits of App Rules
    • How Does Application Control Work?
    • About App Rules Policy Creation
    • Licensing App Rules and App Control
    • Terminology
  • Rules and Policies > App Rules
    • Configuring an App Rules Policy
  • Verifying App Rules Configuration
    • Useful Tools
      • Wireshark
      • Hex Editor
  • App Rules Use Cases
    • Creating a Regular Expression in a Match Object
    • Policy-based Application Rules
    • Logging Application Signature-based Policies
    • Compliance Enforcement
    • Server Protection
    • Hosted Email Environments
    • Email Control
    • Web Browser Control
    • HTTP Post Control
    • Forbidden File Type Control
    • ActiveX Control
    • FTP Control
      • Blocking Outbound Proprietary Files Over FTP
      • Blocking Outbound UTF-8 / UTF-16 Encoded Files
      • Blocking FTP Commands
    • Bandwidth Management
    • Bypass DPI
    • Custom Signature
    • Reverse Shell Exploit Prevention
      • Generating the Network Activity
      • Capturing and Exporting the Payload to a Text File Using Wireshark
      • Creating a Match Object
      • Defining the Policy
• Endpoint Rules
• SonicWall Support
  • About This Document

Creating a Many-to-Many NAT Policy

The many-to-many NAT policy allows you to translate a group of addresses into a group of different addresses. This allows the firewall to utilize several addresses to perform the dynamic translation. If a many-to-many NAT rule policy contains source original and source translated with the same network prefix, the remaining part of the IP address is unchanged.

To create a many-to-many NAT rule policy

1. Navigate to the OBJECT | Match Objects > Addresses page.

   

2. Click +Add at the top of the page. The Address Object Settings dialog displays.

   

3. Enter a description for the address range, such as public_range, in the Name field.

4. Select WAN as the zone from the Zone Assignment drop-down menu.

5. Choose Range from the Type drop-down menu. The Address Object Settings dialog changes.

   

6. Enter the range of addresses (usually public IP addresses supplied by your ISP) in the Starting IP Address and Ending IP Address fields.

7. Click Save to create the range object. The new address object is added to the Address Objects table.

8. Click Close.

9. Navigate to the POLICY | Rules and Policies > NAT page.

10. Click +Add at the bottom of the NAT table. The Adding NAT Rule dialog displays.

11. To create a NAT Rules policy to allow the systems on the LAN subnets (by default, the X0 interface) to initiate traffic using the public range addresses, choose the options shown in Option Choices: Many-to-Many NAT Policy Example:

    Option Choices: Many-to-Many NAT Policy Example

    Option	Value
    Original Source	LAN Subnets
    Translated Source	public_range
    Original Destination	Any
    Translated Destination	Original
    Original Service	Any
    Translated Service	Original
    Inbound Interface	X0
    Outbound Interface	X1
    Comment	Enter a short description
    Enable	Checked
    Create a reflexive policy	(dimmed)

    

12. Click Add to add and activate the NAT Rule policy. The new policy is added to the NAT Policy table.

With this policy in place, the firewall dynamically maps outgoing traffic using the four available IP addresses in the range you created.

You can test the dynamic mapping by installing several systems on the LAN interface (by default, the X0 interface) at a spread-out range of addresses (for example, 192.168.10.10, 192.168.10.100, and 192.168.10.200) and accessing the public website http://www.whatismyip.com from each system. Each system should display a different IP address from the range you created and attached to the NAT policy.

If a many-to-many NAT policy contains source original and source translated with the same network prefix, the remaining part of the IP address is unchanged.