How can I configure BGP (Border Gateway Protocol) with single ISP and advertise your public network?

12/28/2023 185 People found this article helpful 499,547 Views

Description

This article shows you how to configure BGP with single ISP and advertise your public network

Resolution

Resolution for SonicOS 6.5

This release includes significant user interface changes and many new features that are different from the SonicOS 6.2 and earlier firmware. The below resolution is for customers using SonicOS 6.5 firmware.

In this scenario, we configure basic BGP between SonicWall and the ISP's router using CLI(Command Line Interface) to advertise our network (with public IP address) to the ISP. It is necessary to have the AS(Autonomous System) numbers and public IP addresses of both devices. This information should be provided by the ISP

By default, BGP is disabled on SonicWall. To configure BGP follow the steps:

Enable Advanced Routing

Login to your SonicWall management page and click Manage tab on top of the page.
Navigate to Network |Routing page, on right side go to Settings tab.
Under Routing Mode, select Advanced Routing as below.

Click OK button in the pop-up window as below. Click Accept button to save settings.

Enable BGP in SonicWall Management (Configure with CLI)

Login to your SonicWall management page and click Manage tab on top of the page.
Navigate to Network |Routing page, on right side go to Settings tab.
Under Routing Mode: select Advanced Routing
BGP: Enabled (Configure with CLI) (Select this option from Drop-down box).
Click Accept.

NOTE: If you don't see BGP option, you might need a license. Please refer to the following link for more information regarding BGP licensing: UTM: Expanded license for A/A Clustering and BGP

Connect to SonicWall using port 22(SSH)

Configure BGP using CLI

User:admin
Password:

admin@C0EAE45C0360> configure  / Enter to the configure mode admin at GUI from 10.60.2.102 is editing.
Do you wish to preempt them (yes/no)? [no]: yes / Confirm preemption from GUI user who has logged in to SonicWall
config(C0EAE45C0360)#  routing  / Enter to Routing Module
(config-routing)#  bgp / Enter to BGP module ZebOS version 7.7.0 IPIRouter 7/2009
ARS BGP> ARS BGP> configure terminal / Enter configure mode
ARS BGP(config)> router bgp 6501 / Set up AS number on SonicWall
ARS BGP(config-router)> neighbor 2.2.2.1 remote-as 6500 / Configure neighbor connection
ARS BGP(config-router)> network 20.20.20.0 mask 255.255.255.0  / Advertise your network ARS BGP(config-router)> Ctrl+Z / press in Keyboard
ARS BGP> Write / To write the changes into memory and with out this command BGP config will be saved until the firewall is rebooted
ARS BGP> Exit

config(C0EAE45C0360)# commit / To save the configuration

Check BGP neighbor status

ARS BGP> show ip bgp summary
If the output of the command shows any number under State/PfcRcd, it indicates that the neighbors can communicate with each other.

Check the network advertised to the neighbor

ARS BGP> show ip bgp neighbors advertised-routes.

Resolution for SonicOS 6.2 and Below

The below resolution is for customers using SonicOS 6.2 and earlier firmware. For firewalls that are generation 6 and newer we suggest to upgrade to the latest general release of SonicOS 6.5 firmware.

In this scenario, we configure basic BGP between SonicWall and ISP's router using CLI(Command Line Interface) to advertise our network (with public IP address) to the ISP. It is necessary to have the AS(Autonomous System) numbers and public IP address of both devices. This information should be provided by ISP.

By default, BGP is disabled on SonicWall. To configure BGP follow the steps:

Enable Advanced Routing

Navigate to Network | Routing | Routing Mode , select Advanced Routing.

Enable BGP(Configure with CLI)

Navigate to Network | Routing | BGP , select Enable(Configure with CLI).

NOTE: If you don't see BGP option, you might need a license. Please refer to the following link for more information regarding BGP licensing: UTM: Expanded license for A/A Clustering and BGP

Connect to SonicWall using port 22(SSH)

Configure BGP using CLI

User:admin
Password:

admin@C0EAE45C0360> configure / Enter to the configure mode admin at GUI from 10.60.2.102 is editing.
Do you wish to preempt them (yes/no)? [no]: yes / Confirm preemption from GUI user who has logged in to SonicWall
config(C0EAE45C0360)# routing / Enter to Routing Module
(config-routing)# bgp / Enter to BGP module ZebOS version 7.7.0 IPIRouter 7/2009
ARS BGP> configure terminal / Enter configure mode
ARS BGP(config)> router bgp 6501 / Set up AS number on SonicWall
ARS BGP(config-router)> neighbor 2.2.2.1 remote-as 6500 / Configure neighbor connection
ARS BGP(config-router)> network 20.20.20.0 mask 255.255.255.0 / Advertise your network ARS BGP(config-router)> Ctrl+Z / press in Keyboard
ARS BGP> Write / To write the changes into memory and with out this command BGP config will be saved until the firewall is rebooted
ARS BGP> Exit

config(C0EAE45C0360)# commit / To save the configuration

Check BGP neighbor status

ARS BGP> show ip bgp summary
If the output of the command shows any number under State/PfcRcd, it indicates that the neighbors can communicate with each other.

Check the network advertised to the neighbor

ARS BGP> show ip bgp neighbors advertised-routes

Not Finding Your Answers?

ASK THE COMMUNITY

Was This Article Helpful?

YES NO

How can I configure BGP (Border Gateway Protocol) with single ISP and advertise your public network?

Description

Resolution

Resolution for SonicOS 6.5

Resolution for SonicOS 6.2 and Below

Related Articles

Categories

Not Finding Your Answers?

Was This Article Helpful?

Article Helpful Form

Article Not Helpful Form

Follow Us

Subscribe to newsletter

Stay In Touch