• Switch 1.3.0
• Product Overview
  • Package Contents
  • Technical Specifications
  • Supported SonicWall and third-party SFP and SFP+ Modules
  • Physical Interface - 8 Port Switch
  • Physical Interface - 10 Port Switch
  • Physical Interface - 24 Port Switch
  • Physical Interface - 48 Port Switch
  • Device Management
  • Connecting the Switch to a Network
  • Capacity Matrix
• System Management
  • System
    • Dashboard
    • Network
    • Administration
      • SSH Settings
    • System Information
    • User Management
    • Simple Network Management Protocol
      • Classic diagram of SonicWall Switch for SNMP Testing
      • Add View List
      • Add Target Params
      • Add Target Address
      • Add Notify Setting
      • SNMP Traps/Informs
      • How to configure SNMP on SonicWall Switch
      • SNMP supported OID’s in 1.2.0.1-2s
      • How to Configure SNMP/MIB Browser on Client PC
    • Address Resolution Protocol
      • ARP Table
      • ARP Statistics
    • Authentication
    • Firmware and Settings
    • DHCP Snooping
    • DHCP Relay
    • Time
  • Switching
    • Port Settings
      • Port Settings
        • Native VLAN
      • QoS Settings
        • Bandwidth Control
        • Storm Control
      • PoE
      • Security
        • 802.1X
      • ACL Binding
      • Advanced
    • Spanning Tree Protocol
      • Network Loops
      • Global Settings
      • MST Instance Settings
      • STP Port Statistics
    • Loopback Detection
    • Link Aggregation
      • Port Trunking
      • Link Aggregation Control Protocol Settings
      • Link Aggregation Control Protocol Timeout
      • Trunk Port Settings
    • Port Mirror
    • Jumbo Frames
    • MAC Address Table
      • Dynamic MAC Address
      • Search MAC Address
      • MAC Aging Time
    • Link Layer Discovery Protocol
      • Local Device
      • Remote Device
    • IGMP Snooping
      • Global Settings
      • Group List
      • Router Settings
    • Multicast Filtering
    • Quality of Service
      • Class of Service Mapping
      • IP/DSCP Mapping
      • Advanced Mode
        • Class Mapping
          • Adding a Class Policy
        • Policy Mapping
    • Remote Network Monitoring
      • Stat List
      • Event List
      • Event Log Table
      • Statistics
      • Alarm List
      • History List
      • History Log Table
    • Port Statistics
  • Routing
  • Security
    • 802.1X Security
      • MAC Authentication Bypass
        • Behaviors and Restrictions
      • Global Settings
      • Port Settings
      • Authenticated Host
      • Statistics
    • Denial of Service
    • ACL Management
      • MAC ACL
      • MAC-Based ACE
      • IPv4 ACL
      • IPv4-Based ACE
  • VLAN
    • 802.1Q
      • Configuring IGMP Snooping Settings
      • Configuring DHCP Snooping Status
      • Configuring Access and Trunks using Standalone access
    • Voice VLAN
      • OUI Settings
      • Port Settings
  • Logging
    • Global Settings
      • Local Settings
    • Remote Logging
    • Log Table
  • Diagnostics
    • Ping
    • Trace Route
    • Cable Diagnostics
    • Tech Support Report
• System Maintenance
• Switch Troubleshooting
  • Communication flow between Firewall and Switch before it gets authenticated
• SonicWall Support
  • About This Document

Ping

The Packet Internet Groper (Ping)Test allows you to verify connectivity to remote hosts. The test operates by sending Internet Control Message Protocol (ICMP) request packets to the tested host and waiting for an ICMP response. In the process, it measures the time from transmission to reception and records any packet loss. With this diagnostic tool, a ping request is sent to a specified IPv4 address to check whether the switch can communicate with a particular network host.

Test parameters can be varied by entering the data in the appropriate boxes. To verify accuracy of the test, it is recommended to run multiple tests in case of a test fault or user error.